15-Channel Remote Programming

NOTE: P2 is UP and STOP at the exact same time, the light will go around the remote 2 times fast when P2 is selected.

MOTORS WITH RED LEARNING BUTTON — Motor Jogs

Press and hold learning button for the desired number of jogs then release.

  1. One Jog = Pairing mode — press and hold for one jog then release.
  2. Two Jogs = Disable shade — press and hold for two jogs then release — (Recover shade/motor by pressing learning button for one second then release)
  3. Three Jogs = Reverse the motor direction of travel — press and hold for three jogs then release.
  4. Four Jogs = Factory reset — press and hold for four jogs then release.

SECTION 1 — To Sync a Remote To a Shade

  1. Choose channel 1-15 on the remote.
  2. Press and hold learning button until shade jogs and beeps one time.
  3. Press and release P2 on the remote (shade will jog).
  4. Press and release P2 on the remote (shade will beep).
  5. Press and release the up or down button (shade will jog and beep 6 times).

SECTION 2 — Limit Setting Mode

  1. Press and release P2 on the remote (shade will jog and beep one time).
  2. Press the up button on the remote (shade will jog and beep one time).
  3. Press and release P2 on the remote (shade will jog and beep four times) to confirm you are in limit setting mode.
  4. Use the up or down button to move shade to desired upper/lower stop point (for fine tune adjustment press and release P2 while the shade is moving) and press stop. Once you have shade at desired location press and hold the stop button until it beeps four times and jogs once. Shade will jog and beep one time to confirm limit is set.
  5. If limits need to be adjusted after they have been set, please delete limits first (see next section), then start over at section 2.

SECTION 3 — Deleting Limits

  1. Press and release P2 on the remote (shade will jog and beep).
  2. Press the down arrow on the remote (shade will jog and beep).
  3. Press and release P2 on the remote (shade will jog and beep three times to confirm all limits are deleted).

SECTION 4 — Setting Up All Day / All Night Channel

  1. Select individual channel for the motor/shade that you want to add to an “All” channel.
  2. Press and release P2 while on an individual channel (shade will jog and beep).
  3. Press and release P2 again on the same channel (shade will jog and beep).
  4. Select desired “All” channel and press and release P2 on that channel within 7 seconds. Shade is now controlled by its individual channel as well as the all day/all night channel (shade will jog and beep 7 times).
    *NOTE: if shade fails to jog and beep 7 times then the shade may have timed out, start over at Step 1.

Wait 5 seconds before pressing any other buttons

SECTION 5 — Controlling Multiple Motors / Shades With a Single Channel

  1. Start by pairing and setting limits on the first shade/motor (see section 1 and 2).
  2. Press and hold learning button on the first shade for two jogs and release. The motor will beep confirming that it has been disabled.
  3. Move on to the next shade and repeat the above steps (using the same channel).
  4. Once you have all shades/motors programmed, you will recover the disabled shades by pressing and releasing the learning button for about one second.
  5. All shades should now work together.

SECTION 6 — Channel Name Editing Operation

  1. Select the channel you want to edit.
  2. Press Mode button on the back of remote (the first letter of channel name flashes).
  3. Press UP / DOWN button to select desired letter/number after you have reached the desired letter or number, press Channel+ to advance to the next character.
  4. After completing the name edit, press stop to save.

*CLEAR LEARNING BUTTON MOTORS — Motor Jogs

Press and hold learning button for the desired number of jogs then release.

  1. One Jog = Pairing mode — press and hold for one jog then release.
  2. Two Jogs = Reverse the motor direction of travel — press and hold for three jogs then release.
  3. Three Jogs = Factory reset — press and hold for four jogs then release.